Site Information

 Loading... Please wait...

Full Meyer Lyon Rig with 1100-LFC SUBS


Other Details

Limited Warranty
Available upon request
Sales Questions?:



Lyon-M Loudspeakers


Lyon-W Loudspeakers


1100-LFC Subwoofers


RM Server


Galileo Callisto 616


Galileo CAllisto 616 AES


Rain Hood package


Grids, cases, covers, and related accessories


  • Available in two models for greater flexibility: LYON-M for primary array coverage and LYON-W for wide coverage
  • Integrates seamlessly with Meyer Sound’s LEO-M and 1100-LFC
  • High peak power output with exceptional linearity and transient reproduction at any operating level
  • Self-powered for simplified setup and increased reliability
  • Medium- to large-scale applications
  • Arenas, performing arts centres, theatres, churches, and other fixed installations
  • Touring sound reinforcement
  • Downfill, midfill, sidefill, and outfill for LEO-M systems


The self-powered LYON linear line array loudspeaker is a member of Meyer Sound’s LEO Family of linear loudspeakers, designed to reproduce audio faithfully with tremendous power and clarity, without colouring the sound, even when pushed to the limit. LYON delivers the same headroom and precision as the acclaimed LEO-M with the same cutting-edge technology housed in a lighter and more compact cabinet. Optimized rigging and self-powered configuration streamlines both setup and breakdown for LYON systems. LYON is ideal for medium- to large-scale array applications that do not require the extreme long-throw capability of LEO-M.

For greater flexibility, LYON is available in two models: LYON-M for primary array coverage and LYON-W for wide coverage. LYON-W can be used wherever wide coverage is needed in LYON arrays, at the bottom or in the middle of primary arrays, or even at the top of outfill arrays. Because LYON-W matches the acoustical characteristics and vertical coverage of LYON-M, transitions for horizontal coverage are seamless. Both LYON models are matched acoustically to LEO-M and can be used for downfill and midfill at the bottom of LEO-M arrays, and as supplemental sidefill and outfill arrays in LEO-M systems.

LYON arrays are ideally paired with Meyer Sound’s 1100-LFC low-frequency control element for bass reproduction. Entire systems are driven by Meyer Sound’s Galileo Callisto 616 array processor, which provides matrix routing, alignment, and processing for array components. To guarantee optimum system performance, including coverage patterns and maximum peak SPL, LYON systems should be designed with Meyer Sound’s MAPP Online XT™ acoustical prediction software.

LYON’s high-frequency section is comprised of two proprietary compression drivers coupled to a constant-directivity horn through a patented REM™ manifold. The manifold’s smooth radiating characteristics afford tight vertical coverage. The low-frequency section includes two long excursion cone drivers, also proprietary, capable of withstanding high, continuous output levels. Precise phase and magnitude alignment between low- and high-frequency drivers yields consistent and well-behaved system responses.

The unit’s onboard power amplifier operates at nominal voltages from 85–134 V AC and 165–264 V AC at 50–60 Hz. TruPower limiting ensures maximum driver protection, minimizing power compression while yielding high constant output under high continuous and peak power conditions. The amplifier, control electronics, and power supply are contained in a single field-replaceable module located on the rear of the cabinet.

Meyer Sound’s RMS remote monitoring system comes standard with all LYON loudspeakers and provides comprehensive monitoring of system parameters on a Mac or Windows-based computer. Convenient XLR 5-pin connectors allow the use of composite cables carrying both RMS and balanced audio. XLR 3-pin audio connectors are also available.

LYON offers intuitive rigging with captive Guide-A-Links that can be set to the desired splay angles while cabinets rest in caster frames. The MTG-LYON top grid flies’ arrays of up to 18 LYONs at a 7:1 safety factor (with some restrictions). The optional MTF-LEO/LYON transition frame flies LYONs at the bottom of LEO-M arrays. Stacks of up to four LYON cabinets can be securely transported with the optional MCF-LYON caster frame; durable nylon covers, accommodating stacks of two, three, or four units, are available to protect the cabinets during transport.

The LYON cabinet is constructed of multi-ply hardwood and coated with a black-textured finish. A hex-stamped, steel grille with acoustical black mesh protects the unit’s drivers. Other options include weather protection and custom colour finishes for fixed installations and applications with specific cosmetic requirements.



Operating Frequency Range

55 Hz – 16.5 kHz

Note: Recommended maximum operating frequency range. Response depends on loading conditions and room acoustics.

Phase Response

80 Hz to 16 kHz ±30 degrees


Low Frequency

Two 12-inch long-excursion cone drivers

High Frequency

Two 3-inch compression drivers coupled to a constant-directivity horn through a patented

REM® manifold



Differential, electronically balanced

Maximum Common Mode Range

±15 V DC, clamped to earth for voltage transient protection


XLR 3-pin or 5-pin female input

XLR 3-pin or 5-pin male loop output

Note: XLR 5-pin connectors accommodate both balanced audio and RMS signals.

Input Impedance

10 kOhm differential between pins 2 and 3


Pin 1: Chassis/earth through 1 kOhm, 1000 pF, 15 V clamped network to provide virtual

ground lift at audio frequencies

Pin 2: Signal (+) Pin 3: Signal (–)

Pin 4: RMS (polarity insensitive) Pin 5: RMS (polarity insensitive) Case: Earth ground and chassis

Note: Pins 4 and 5 (RMS) included only with XLR 5-pin connectors.

DC Blocking

Differential DC blocking up to the maximum common mode voltage


>50 dB, typically 80 dB (50 Hz – 500 Hz)

RF Filter

Common mode: 425 kHz

Differential mode: 142 kHz

TIM Filter

Integral to signal processing (<80 kHz)

Nominal Input Sensitivity

0.0 dBV (1.0 V rms) continuous is typically the onset of limiting for noise and music

Input Level

Audio source must be capable of producing +20 dBV (10 V rms, 14 V peak) into

600 ohms to produce the maximum peak SPL over the operating bandwidth of the loud- speaker



3-channel, complementary MOSFET output stages (class AB/H bridged)


Two ultrahigh-speed primary fans, two ultrahigh-speed reserve fans



powerCON 32 input

Safety Rated Voltage Range

95–125 V AC, 50–60 Hz

208–235 V AC, 50–60 Hz

Turn-on/off Points

Turn-on: 85 V AC; Turn-off: 134 V AC

Turn-on: 165 V AC; Turn-off: 264 V AC

Current Draw


0.7 A rms (208 V AC)

0.6 A rms (230 V AC)

1.2 A rms (115 V AC)

Maximum Long-Term Continuous

6.2 A rms (208 V AC)

5.6 A rms (230 V AC)

11.2 A rms (115 V AC)


8.2 A rms (208 V AC)

7.5 A rms (230 V AC)

15.4 A rms (115 V AC)

Maximum Instantaneous Peak

25 A peak (208 V AC)

23 A peak (230 V AC)

45 A peak (115 V AC)


<15 A peak (208 V AC)

<15 A peak (230 V AC)

<15 A peak (115 V AC)



Multi-ply hardwood


Black textured

Protective Grille

Hex-stamped steel with acoustical black mesh


Endframes with captive GuideALinks (0.0 to 9.0-degree splay angles), quick-release pins, and detachable side handles


38.15 inches (969 mm) W

14.85 inches (377 mm) H

21.00 inches (533 mm) D


199 lbs (90.3 kg)


Operating Temperature

0° C to +45° C

Non-Operating Temperature

–40° C to +75° C


To 95% at 45° C (non-condensing)

Operating Altitude

To 5,000 m (16,404 ft)

Non-Operating Altitude

To 12,000 m (39,000 ft)


30 g 11 msec half-sine on each of 6 sides


10 Hz – 55 Hz (0.010 m peak-to-peak excursion)




Architect Specifications

The loudspeaker shall be a self-powered, linear, low-distortion, line array loudspeaker. Its transducers shall include two 3-inch compression drivers coupled to a constant-directivity horn through a patented REM manifold, and two 12-inch long-excursion cone drivers.

The loudspeaker shall incorporate internal processing and a 3-channel class AB/H bridged amplifier with complementary MOSFET output stages. Protection circuits shall include TruPower limiting. The audio input shall be electronically balanced with a 10 kOhm impedance and accept a nominal 0 dBV (1.0 V rms) signal (+20 dBV to produce maximum SPL). Audio connectors shall be XLR 3-pin, female and male, accommodating balanced audio, or XLR 5-pin, accommodating both balanced audio and RMS. RF filtering shall be provided, and CMRR shall be greater than 50 dB (50 Hz – 500 Hz).

Performance specifications for a typical production unit shall be as follows, measured at 1/3-octave resolution: operating frequency range, 55 Hz to 16.5 kHz; phase response, 80 Hz to 16 kHz ±30 degrees.

The internal power supply shall perform EMI filtering, soft current turn-on, and surge suppression. Power requirements shall be nominal 100, 110, or 230 V AC line current at 50–60 Hz. UL and CE operating voltage ranges shall be 95–125 V AC and 208–235 V AC at 50–60 Hz. Current draw during burst shall be 7.5 A rms at 230 V AC and 15.4 A rms at 115 V AC. Current inrush during soft turn-on shall not exceed 15 A at 230 V AC. The AC power connector shall be a powerCON 32. The loudspeaker shall include an RMS remote monitoring system module.

Components shall be mounted in an optimally tuned, vented enclosure constructed of multi-ply hardwood and coated with a black-textured finish. Dimensions shall be 38.15” wide x 14.85” high x 21.00” deep (969 mm x 377 mm x 533 mm). Weight shall be 199 lbs (90.3 kg).

The loudspeaker shall be the Meyer Sound LYON.

  • RM Server

Other Details

Limited Warranty
Available upon request
Sales Questions?:

Find Similar Products by Tag

Find Similar Products by Category

Click the button below to add the Full Meyer Lyon Rig with 1100-LFC SUBS to your wish list.